Adlink Express-LPC Manual de usuario Pagina 53
- Pagina / 86
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Page 53Express-IA533 User’s Manual Page 53Express-IA533 User’s ManualExpress-LPC User’s Manual Page 53
8.3.8 PCI Express Configuration
You can use this screen to specify options for the PCI Express Configuration Settings.
Active State Power-Management
This option allows you to enable/disable the Active State Power Management (ASPM)
function. ASPM is a PCIe power management specification.
PCIE Ports 0-3 Configuration
Allows you to configure the PCIE0~PCIE3 of the south bridge as one x4 slot or four x1 slots.
This function is only available on the Extended Version module supporting six PCIe x1.
PCIE Port (0-5) IOxAPIC Enable
This function is used to control the availability of the PCIE Port 0~5 IOxAPIC.
PCIE High Priority Port
This function is used to select a PCIE port as high priority port. Transactions on this port
have higher priority than other ports.
- Express-LPC 1
- Revision History 2
- Table of Contents 3
- Disclaimer 5
- Environmental Responsibility 5
- Trademarks 5
- Conventions 6
- 1 Introduction 7
- 2 Specifications 8
- 2.3 Audio 9
- 2.5 Multi I/O 9
- 2.7 Super I/O 9
- 2.8 Power Specifications 10
- 3 Functional Diagram 11
- 4 Mechanical Dimensions 12
- 5.1 COM Express 13
- Type 2 compatible pinout 13
- 5.3 Pin Definitions 14
- Pin Definitions (cont’d) 15
- 5.4 Signal Descriptions 16
- Signal Descriptions (cont’d) 17
- 6 Embedded Functions 25
- 6.2 GPIO 26
- 6.3 Hardware Monitoring 27
- 7 System Resources 28
- 7.3 Legacy I/O Map 29
- Legacy I/O Map (cont’d) 30
- PIC Mode 30
- APIC Mode 31
- 7.6 PCI Interrupt Routing Map 32
- 8 BIOS Setup Utility 33
- 8.1.1 Main Setup Menu 34
- 8.1.2 Navigation 35
- 8.2 Main Setup 37
- 8.3 Advanced BIOS Setup 38
- 8.3.1 CPU Configuration 39
- CPU Configuration Settings 39
- Max CPUID Value Limit 39
- 8.3.2 Chipset Configuration 41
- DRAM Frequency 41
- Configure DRAM Timing by SPD 41
- APIC ACPI SCI IRQ 41
- Internal Graphics Mode Select 42
- DVMT Mode Select 42
- 8.3.4 IDE Configuration 44
- IDE Configuration Settings 44
- ATA/IDE Configuration 44
- Legacy IDE Channels 44
- Hard Disk Write Protect 45
- IDE Detect Time Out 45
- ATA(PI)80Pin Cable Detection 45
- 8.3.5 AHCI Configuration 45
- AHCI Ports 46
- Onboard LAN Boot ROM 47
- HD Audio Controller 47
- SMBus Controller 47
- SuperIO Configuration Screen 48
- Floppy A 48
- OnBoard Floppy Controller 48
- Serial Port1 Address 49
- Serial Port2 Address 49
- Parallel Port Address 49
- Parallel Port Mode 49
- 8.3.7 USB Configuration 50
- USB Configuration Settings 50
- Parallel Port IRQ 50
- Active State Power-Management 53
- PCIE Ports 0-3 Configuration 53
- PCIE High Priority Port 53
- Remote Access 55
- Serial Port Number 55
- Remote Access Configuration 55
- Option Description 56
- 8.3.11 Trusted Computing 57
- Execute TPM Command 57
- 8.4 Power Management 58
- ACPI Aware O/S 59
- ACPI Version Features 59
- ACPI APIC Support 59
- USB Device Wakeup from S3/S4 59
- AMI OEMB Table 59
- Suspend mode 60
- Headless mode 60
- Restore on AC Power Loss 60
- ACPI OS Shutdown Mode 60
- Power Management/APM 61
- Power Button Mode 61
- Suspend Time Out 61
- 8.4.2 APM Configuration 61
- Video Power Down Mode 62
- Throttle Temperature 63
- Throttle Duty 63
- Critical Temperature 63
- 8.5 Boot Setup 64
- Quick Boot 65
- Quiet Boot 65
- AddOn ROM Display Mode 65
- Bootup Num-Lock 66
- PS/2 Mouse Support 66
- Wait for ‘F1’ If Error 66
- Hit ‘DEL’ Message Display 66
- Interrupt 19 Capture 66
- Boot Device Priority 67
- Boot Device Groups 67
- 8.6 Security Setup 68
- 8.6.3 Change User Password 70
- 8.6.4 Clear User Password 70
- 8.7 Exit Menu 71
- Discard Changes 72
- Load Optimal Defaults 72
- Load Failsafe Defaults 72
- Viewing BIOS Checkpoints 73
- 9.3 POST Code Checkpoints 76
- POST Code Checkpoints cont’d: 77
- 9.5 DIM Code Checkpoints 78
- 9.6 ACPI Runtime Checkpoints 79
- 9.7 Boot Block Beep Codes 80
- 9.8 POST BIOS Beep Codes 80
- Important Safety Instructions 82
- Getting Service 84
Relacionado con productos y manuales para Hardware Adlink Express-LPC
Hardware Adlink Express-BASE Manual de usuario
(46 paginas)
(46 paginas)
Hardware Adlink nanoX-BT Manual de usuario
(71 paginas)
(71 paginas)
Hardware Adlink nanoX-TC Manual de usuario
(62 paginas)
(62 paginas)
Hardware Adlink nanoX-TCR Manual de usuario
(50 paginas)
(50 paginas)
Hardware Adlink nanoX-BASE Manual de usuario
(44 paginas)
(44 paginas)
Hardware Adlink LEC-BTS Manual de usuario
(22 paginas)
(22 paginas)
Hardware Adlink LEC-iMX6 Manual de usuario
(28 paginas)
(28 paginas)
Hardware Adlink LEC-3517 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Adlink LEC-BASE R1 Manual de usuario
(30 paginas)
(30 paginas)
Hardware Adlink ETX-BT Manual de usuario
(70 paginas)
(70 paginas)
Hardware Adlink ETX-CV Manual de usuario
(86 paginas)
(86 paginas)
Hardware Adlink ETX-PVR Manual de usuario
(68 paginas)
(68 paginas)
Hardware Adlink ETX-Proto Manual de usuario
(38 paginas)
(38 paginas)
Hardware Adlink CoreExpress-ECO2 Manual de usuario
(36 paginas)
(36 paginas)
Hardware Adlink Hurricane-QM57 Manual de usuario
(30 paginas)
(30 paginas)
Hardware Adlink CoreExpress-ECO2 Manual de usuario
(38 paginas)
(38 paginas)
Hardware Adlink MXC-6300 Series Manual de usuario
(124 paginas)
(124 paginas)
Hardware Adlink MXC-6000 Series Manual de usuario
(100 paginas)
(100 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales