Adlink aTCA-9710 Manual de usuario

aTCA-9710 Dual Intel Xeon E5-2658 v3 40G AdvancedTCA Processor Blade User’s Manual Manual Revision: 0.10 Preliminary Revision Date: J

102.2 Power Consumption This section provides information on the power consumption of the aTCA-9710. System configuration (1) Memory: 16x 8GB DDR4

112.3 Board Layout 2.3.1 aTCA-9710 Board Layout - Component Side Location Description Location Descriptio

122.3.2 aTCA-9710 Board Layout - Solder Side Location Description SW2 Clear CMOS SW6 HW Reset Button SW6 SW2

132.3.3 aTCA-9710 Front Panel VGA10GbE (SFP) USBIPMC Serial Debug PortRS-232 Serial Port Base and Fabric Channel LEDsReset

14 2.3.4 Status LED Definitions The following sections describe the front panel Status LEDs: Hot-swap LED, OOS LED, BIOS/OS Boot OK LED, IPMC Paylo

152.3.4.4 IPMC Chassis Identify Command LED IPMC Chassis Identify Command (Amber) State Remark Off Default Off Blinking Chassis Identify Comman

162.3.4.6 Base and Fabric Channels LEDs Base and Fabric Channels LEDs FCH1 ACT (Amber) Blink when accessing Ethernet I/O Fabric 1 Link (Amber) 40

172.4 Compliance The aTCA-9710 conforms to the following specifications:  PICMG 3.0 R2.0 ECN0002 AdvancedTCA  PICMG 3.1 Ethernet over AdvancedT

183 Functional Description 3.1 CPU, Memory and Chipset 3.1.1 CPU The Intel® Xeon® processor E5-2658 v3 implements several key technologies:  Fou

193.1.2 Memory The aTCA-9710 is a dual processor system with each Intel® Xeon® processor E5 2600 v3 series providing four memory channels supporting

2Revision History Revision Release Date Description of Change(s) 0.10 27/01/2015 Preliminary release Copyright 2015 ADLINK Te

20 3.1.4 Silicon Motion SM750 Graphics Controller The aTCA-9710 provides an analog VGA port on the front panel powered by a Silicon Motion SM750 2D

21 3.2.2 SMBus Devices The aTCA-9710 provides a System Management Bus (SMBus) hosted by the Intel® C612 PCH. The topology is shown in the diagram bel

22 3.3 I/O Interfaces 3.3.1 USB The aTCA-9710 supports Five USB 2.0 ports:  3x Type-A ports on front panel  Two ports routed to RTM (available

23 3.3.2 VGA Interface A DB-15 female connector on the front panel provides analog display output. Front Panel VGA Pin Definition (DB-15)

24 3.3.4 Serial Port Two serial ports are output to USB Mini-B connectors on the front panel for use as service terminals. The port labeled IPMI i

25 3.3.6 Switch And Jumper Settings 3.3.6.1 Set Blade Operation Mode Use switch SW4 to set the Blade Operation Mode. Normal operation requires a

26 4 Intelligent Platform Management System The purpose of the intelligent platform management system is to monitor, control, and assure proper ope

27Threshold Sensor Type LNR LC LNC UNC UC UNR 12.0V SYS Volts 13.24 13 12.76 11.32 11.08 10.84 1.05V VCCIO Volts 1.216 1.168 1.104

284.1.1 Sensor Reading (FRU Hotswap Sensor) Byte Data field Request data 1 Sensor Number (FFh = reserved) 1 Completion Code 2 Sensor Reading.

294.1.2 Get Sensor Reading (Physical IPMB-0 Sensor) Byte Data field Request data 1 Sensor Number (FFh = reserved) 1 Completion Code 2 [7] – I

3Table of Contents Revision History ...

304.1.3 Watchdog Timer Sensor Sensor Type Sensor Type Code Sensor Specific Offset Event Watchdog 2 23h 00h 01h 02h 03h 04h-07h 08h This senso

314.1.4 Version Change Sensor Sensor Type Sensor Type Code Sensor Specific Offset Event Version Change 2Bh 00h 01h 02h 03h 04h 05h 06h

324.1.5 System Firmware Progress Sensor Sensor Type Sensor Type Code Sensor Specific Offset Event System Firmware Progress (formerly POST Error

33Sensor Type Sensor Type Code Sensor Specific Offset Event 13h Starting operating system boot process, e.g. calling Int 19h 14h Basebo

34 Byte Data field [2] - 1b = state 2 asserted [1] - 1b = state 1 asserted [0] - 1b = state 0 asserted (5) For discrete reading sensors only. (Op

354.2 IPMI Commands The following table presents all the commands which are supported by the aTCA-9710 in different interfaces and compatible with

36PICMG Command HPM.1 Upgrade Commands (HPM.1) Get target upgrade capabilities ● ● Get component properties ● ● Abort Firmware Upgrade ● ● Initi

37 5 Getting Started The aTCA-9710 has been designed for easy installation. However, the following standard precautions, installation procedures, a

38 5.2 Installing and Removing the aTCA-9710 5.2.1 Installing the Blade Follow these steps to install the aTCA-9710 blade to the chassis.

39Step 2 Check if the catch hooks and alignment pins at both ends of the module are correctly inserted into the proper openings. Push inwards on th

45.3 Firmware Update Procedure...45 5.3.1 Update

40Step 3 Push the ejector handles inwards until it is locked.

41Step 4 Lock both ends of the captive screws.

42 5.2.2 Removing the Blade Follow these steps to remove the aTCA-9710 blade from the chassis. Step 1 Unlock both ends of the captive screws.

43Step 2 Pinch the lever and latch together then pull outwards to release the ejector handles at both ends. Lever Latch

44Step 3 Pull the blade outwards from the chassis until it is removed.

455.3 Firmware Update Procedure The aTCA-9710 supports firmware update (IPMC FW, BIOS, FRU) over various interfaces (LAN, KCS, serial interface or

46 5.3.2 Update over KCS Step1: Prepare an aTCA-9710 with Linux system. Enter the following command to make sure the ipmi_si and ipmi_devintf

47 5.3.3 Update over LAN The following IPMItool command line parameters are used for communicating with the carrier IPMC via LAN:  -I lan The

486 BIOS This chapter will guide you how to configure BIOS setup items. There will be detailed description for each BIOS setup item in the following

49keys, and so on. There is a hot key legend located in the right frame on most setup screens.. →← Left/Right. The Left and Right < A

5 1 Overview 1.1 Introduction The ADLINK aTCA-9710 is a high performance AdvancedTCA® (ATCA) processor blade featuring dual 12-core Intel® Xeon® Pro

506.2 Main BIOS Setup Screen The Main BIOS setup menu is the screen where you start navigation of the BIOS setting menus. You can always return to t

51 The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and 5:30 P.M. as 17:30:00. System & Board Information The Main

526.3 Advanced Setup Screen Select the Advanced tab from the setup screen to enter Advanced BIOS setup screen. You can select any of items in the

53Fabric 40G LAN3/4 PXE ROM Enable or Disable PXE ROM OF Fabric 40G LAN3/4. Set this value to Enabled / Disabled. RTM 10G LAN1/2 PXE ROM Enable

546.3.1 ACPI Settings You can use this screen to select options for the ACPI Advanced Configuration Settings. Use the up and down < Arrow >

556.3.2 NCT5104D Super IO Configuration You can use this screen to select options for the NCT5104D Super IO Configuration. Use the up and down <

56 Serial PortGSIO200 Enable or Disable Serial Port (COM). Set this value to Enabled / Disabled

576.3.3 Serial Port Console Redirection You can use this screen to select options for the serial port console redirection settings. Use the up and

58 Terminal Type VT100+ is the preferred terminal type for out-of-band management. Configuration options: VT100, VT100+, VT-UTF8 , ANSI. Bits pe

59Flow Control Set this option to select Flow Control for console redirection. The settings for this value are None, Hardware RTS/CTS. VT-UTF8 C

61.2 Block Diagram

606.3.4 PCI Subsystem Settings You can use this screen to select options for the PCI Subsystem Settings. Use the up and down < Arrow > keys

616.3.5 Network Stack Configuration You can use this screen to select options for the Network Stack Configuration. Use the up and down < Arrow

62 Media detect count Number of times presence of media will be checked. Set this value to integer. 6.3.6 CSM Configuration You can use this scre

63 Storage Controls the execution of UEFI and Legacy PXE OpROM. Set this value to Do not launch / UEFI / Legacy 6.3.7 Trusted Computing Trusted co

646.3.8 ADLINK IPMI settings You can use this screen to select options for the ADLINK IPMI settings. Use the up and down < Arrow > keys to s

65OS Load Watchdog Timeout Select the time value for OS Watchdog Timer Expiration value. Set this value to 5 minutes / 10 minutes / 15 minutes / 2

666.4 Intel RC Setup Select the Inte lRC Setup tab from the setup screen to enter the Intel RC Setup screen. You can select any of the items in the

67 Hyper-Threading [ALL] Enables Hyper Threading (Software Method to Enable/Disable Logical Processor threads. Set this value to Enabled / Disable

68 Cores Enabled Number of Cores to Enable. 0 means all cores.

696.4.2 Advanced Power Management Configuration You can use this screen to select options for the Advanced Power Management Configuration. Use the

7 1.3 Package Contents Before opening, please check the shipping carton for any damage. If the shipping carton and contents are damaged, notify th

70 EIST (P-states) When enabled, OS sets CPU frequency according load. When disabled, CPU frequency is set at max non-turbo. Set this value to Ena

71 ACPI T-States Enable/Disable CPU throttling by OS. Throttling reduces power consumption. Set this value to Enable/Disable. 6.4.3 Common RefCo

72 Numa Enable or Disable Non uniform Memory Access (NUMA). Set this value to Enable/Disable. 6.4.4 Memory Configuration You can use this scree

73 Memory Map Set memory mapping settings. The screen is shown below

74Socket Interleave Below 4GB Splits the 0-4GB address space between two sockets, so that both sockets get a chunk of local memory below 4GB. Set t

75The screen is shown below Intel VT for Directed I/O (VT-d) The screen is shown below PCIe x8 to aDB-9710 Selects PCIe port Bifurcation for se

766.4.6 PCH Configuration You can use this screen to select options for the PCH Configuration. Use the up and down < Arrow > keys to select a

77 Configure SATA as This will configure SATA as IDE ,RAID or AHCI. Set this value to IDE/AHCI/ RAID .

786.5 Server Mgmt Setup Screen You can use this screen to specify options for the Server Management settings. Use the up and down <Arrow> ke

796.6 Boot Setup Screen You can use this screen to specify options for the Boot configuration settings. Use the up and down <Arrow> keys t

82 Specifications 2.1 aTCA-9710 Specifications 2.1.1 CPU/ Chipset/ Memory CPU Dual 12-core Intel® Xeon® Processor E5-2658 v3, (2.2/2.9GHz QPI 9.6

80 6.7 Security Setup Screen System BIOS provides two levels of password protection. They are Administrator password and User password. The system

816.8 Save & Exit Setup Screen Select Save & Exit tab from setup utility to enter Save & Exit BIOS setup screen. You can select an it

82Discard Changes and Exit? [OK] [Cancel] Select OK and press <Enter> to discard changes and exit. It will keep booting the system to OS. Sa

837 Serial Over LAN Serial Over LAN (SOL) is a remote management feature that allows the IPMC (Smart Fusion A2F500) to redirect the serial console

84Build the source code and install IPMItool: make make install Now your remote client is ready to connect to the target the aTCA-9710. Note: Th

857.3.3 Linux System Setting Linux needs to be told to listen for logins on the serial port. This is done by adding the following line to /etc/init

86 The default values of the aTCA-9710 SOL parameters are listed in the table below Parameter Default Value Channel 1 IP Address 172.17.172.134 Ch

87 8 Drivers The drivers for aTCA-9710 are available on the ADLINK website. Please visit the aTCA-9710 product web site for more details: www.adli

88Safety Instructions 1. Please read these safety instructions carefully. 2. Please keep this User‘s Manual for later reference. 3. One AC Inle

89Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe Di

9 2.1.3 Software BIOS AMI BIOS with 8Mbit flash memory Supported OS Microsoft Windows Server 2012 R2 Red Hat Enterprise Linux 6.x/7.0 Contact ADLINK

90 ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1 60 12 35